HAKRC M10 GPS Module with QMC5883 Compass

Short Description:

HAKRC M10 GPS module for FPV and RC aircraft with an M10050 receiver, QMC5883 compass, 5 V input, and a default 10 Hz navigation update rate.

Product Name: HAKRC M10 GPS Module with QMC5883 Compass
GPS Type: Multi-GNSS positioning module with an integrated compass
GNSS Platform: u-blox M10, M10050 receiver chip
Supported Systems: M10050 platform supports GPS, Galileo, BeiDou and GLONASS, with QZSS and SBAS support. Enabled systems depend on configuration.
Positioning Accuracy: 1.5 m horizontal CEP as an M10050 reference with GPS/Galileo and SBAS/QZSS
Update Rate: 10 Hz default. Product label lists 0.25–18 Hz, subject to configuration.
Interface: UART for GNSS at 115200 bps as labeled. I²C via SCL and SDA for the compass.
Operating Voltage: 5.0 V DC module input
Magnetometer: QMC5883 onboard compass
Listed Module Size: 25 × 25 mm as listed

Send email to us

Product Detail

FAQ

Technical Highlights

M10050 GNSS Receiver

The HAKRC M10 provides satellite positioning for FPV multirotor and RC fixed-wing builds. The module label specifies a default 10 Hz navigation update rate and a serial baud rate of 115200 bps.

Integrated QMC5883 Compass

The onboard QMC5883 supplies magnetic heading data over I²C. A flight controller can receive GNSS data through UART and access the compass through its SCL and SDA connections.

5 V Supply and Six-Pin Connection

The board brings power, ground, UART and I²C to a six-pin connector. The same signals are available on labeled solder pads.

Technical Specifications

Model	HAKRC M10 GPS
GNSS Receiver	u-blox M10050
GNSS Platform Support	GPS, Galileo, BeiDou and GLONASS, plus QZSS and SBAS. Enabled systems depend on receiver configuration.
Horizontal Accuracy Reference	1.5 m CEP at receiver level with GPS/Galileo and SBAS/QZSS. Installed performance depends on antenna placement and signal conditions.
Navigation Update Rate	10 Hz default. The module label lists 0.25–18 Hz, subject to receiver configuration.
GNSS Messaging	The M10050 platform supports UBX and NMEA over UART. Match the flight-controller setting to the enabled output.
Magnetometer	QMC5883, I²C
Module Input	5.0 V DC
Listed Module Size	25 × 25 mm. Confirm thickness and connector clearance for a close-fitting mount.

Flight-Controller Wiring

Module Signal	Flight-Controller Connection
TX	UART RX
RX	UART TX on the same port
5 V / VCC	Regulated 5 V output
GND	Ground
SCL	I²C SCL for the compass
SDA	I²C SDA for the compass

FAQ

Which connections are needed for GPS and compass data?

GNSS data uses UART TX and RX. To use the onboard QMC5883 compass, also connect I²C SCL and SDA and configure compass support in the flight-controller firmware.

What voltage and baud rate does the module use?

The module label specifies 5.0 V DC input and 115200 bps for the GNSS UART. Match the flight controller's serial settings to the receiver configuration.

What is the default navigation update rate?

The module is labeled for a default rate of 10 Hz and a listed range of 0.25–18 Hz. The usable rate depends on the receiver settings and active constellation combination.

B2B Procurement FAQ

What should I specify when requesting a quotation?

Provide the HAKRC M10 model name, required quantity and any requirements for the QMC5883 compass, GNSS output protocol or harness pinout.

How can I confirm fit with an existing mount or harness?

Request the dimensions, connector clearance and pin assignment for the supplied revision. Include your available mounting space and the mating connector details in the inquiry.

Is the six-wire harness supplied with the module?

The product image shows a six-wire harness alongside the module. Confirm the included items, order quantity and lead time in the quotation.